CABLES

Solar Adapter Cable MC4/F to MC3/M 15cm is a short adapter cable linking an MC4 female connector to an MC3 male connector, used to connect solar panels or equipment that use different connector systems.

Solar Splitter Pair MC4-Y, 1x M-2F / 1x F-2M is a set of two MC4 Y-splitters, one male to 2x female and one female to 2x male, used to connect two solar panels in parallel on a single cable run.

Solar Connector Pair MC4, 1x Male/1x Female is a set of one MC4 male and one MC4 female connector, used to assemble or repair PV cables and connect them to solar panels or charge controllers.

Solar Adapter Cable MC4/M to MC3/F 15cm is a short adapter cable linking an MC4 male connector to an MC3 female connector, used to connect solar panels or equipment that use different connector systems.

Solar Cable 20m/6mm² MC4-M/F (PV-ST01) is a pre-assembled 20 m PV cable with MC4 male and female connectors, intended for longer runs between the PV array and the charge controller.

Solar Cable 10m/6mm² MC4-M/F (PV-ST01) is a pre-assembled 10 m PV cable with MC4 male and female connectors, intended for longer runs between the PV array and the charge controller.

Solar Cable 5m/6mm² MC4-M/F (PV-ST01) is a pre-assembled 5 m PV cable with MC4 male and female connectors, suitable for extending the connection between solar panels and the charge controller.

Solar Cable 3m/6mm² MC4-M/F (PV-ST01) is a pre-assembled PV cable with an MC4 male connector at one end and a female one at the other, used to connect solar panels to each other or to the charge controller.

Solar Cable 5m/4mm² MC4-M/F (PV-ST01) is a pre-assembled 5 m PV cable with MC4 male and female connectors, suitable for extending the connection between solar panels and the charge controller.

Solar Cable 3m/4mm² MC4-M/F (PV-ST01) is a pre-assembled PV cable with an MC4 male connector at one end and a female one at the other, used to connect solar panels to each other or to the charge controller.

Solar Cable 1m/6mm² MC4-M/F (PV-ST01) is a pre-assembled PV cable with an MC4 male connector at one end and a female one at the other, used to connect solar panels to each other or to the charge controller.

Solar Cable 1m/4mm² MC4-M/F (PV-ST01) is a pre-assembled PV cable with an MC4 male connector at one end and a female one at the other, used to connect solar panels to each other or to the charge controller.

Pre-charge cable is an accessory that pre-charges the internal capacitors of an inverter, inverter/charger or MPPT via the DC terminals before the battery is connected, so that connecting the battery does not cause arcing.

USB extension cable 0.3 m one side right angle is an accessory for USB connections inside the Color Control GX wall mount box, where some USB plugs are too long to fit.

VE.Can to CAN-bus BMS type A Cable 1.8 m is a cable for connecting a CAN-bus enabled battery from another manufacturer to a Victron system. The manual indicates whether type A or B is needed for each battery brand.

VE.Can Power Cable is a cable that supplies power to the CAN bus. It is needed when the VE.Can network is not powered by a Skylla-i charger or an MPPT.

VE.Direct TX digital output cable is a cable used in combination with BlueSolar and SmartSolar MPPT solar chargers. It supports solar lighting applications and a virtual load output.

Non-inverting remote on-off cable is a cable that connects Skylla-TG chargers and Battery Protect models BP40i, BP60i and BP200i to a VE.Bus BMS, translating its remote on/off signal to the logic these products need.

Inverting remote on-off cable is a control cable that connects Phoenix inverters rated 3 kVA and more and all Multi, MultiPlus and Quattro units to a VE.Bus BMS or to the load output of a BlueSolar MPPT charger.

VE.Direct to USB-C interface is a cable that connects products with a VE.Direct port to devices with a USB port, such as a computer. It also allows more than two VE.Direct products to be connected to a single CCGX.